
VIP technology
What is a VIP?
The vacuum insulation panel (VIP for short) is a highly efficient insulating material which, thanks to the vacuum inside it, requires only a fifth of the thickness of conventional materials (such as mineral wool) to achieve comparable insulation values.
To put it very simply, it can be compared to a slim packet of coffee. In both cases, the contents are vacuum-packed in a metallised foil wrapper.
- High-performance insulation material
- Thermal conductivity < 0.004
- Non-combustible core material
- Recyclable
Cross-section
Structure of a VIP

The picture shows an open vacuum insulation panel. The core can be produced either by a pressing process or by pouring in the powdered material. The image shows a pressed core, which is therefore dimensionally stable. This is further protected by a non-woven fabric covering and is then sealed under vacuum (at approx. 0.01–10 mbar, depending on the core material) into a gas- and water-vapour-tight film.

main ingredient
Fumed silica as core material
The core of high-quality vacuum insulation panels (VIPs) consists of silicon dioxide, specifically pyrogenic silica. Cheaper alternatives often use glass fibres, but these come with environmental and technical drawbacks. Vaku-Isotherm therefore relies exclusively on silica-based VIPs.
Silicic acid is extracted from sand and produced either via flame processes (pyrogenic) or by the water glass process (precipitated silicon dioxide). This results in a microporous structure with pore sizes of 5–50 nanometres – a key factor in the excellent insulating performance of VIPs. Even if the vacuum is lost, the insulating properties remain outstanding thanks to this structure. Although the value drops from approx. 0.004 W/mK (initial) to 0.020 W/mK, the material still insulates significantly better than, for example, mineral wool at 0.035 W/mK.
The core material also impresses with its high thermal stability and non-combustibility. Accordingly, we also market the pure core material as a product in its own right, as an alternative to other fire protection materials that provide significantly poorer insulation. Our CorePAN product has fire resistance class A2.
Insulating effect
Minimal heat transfer
Heat transfer can take the form of solid-state conduction, infrared radiation or convection. For ideal insulation, the aim is to minimise all three of these factors.
With VIPs, there is only a small contact area between the individual particles (5–50 nm), which reduces solid-state heat conduction to a minimum. Convection is minimised by the subsequent pressing process of the silica. The pores are then so small that the gas molecules are able to collide with one another only very rarely.
The addition of opacifying agents to the core reduces infrared radiation to a minimum. Even in its non-evacuated state, the core material thus has a good thermal conductivity of approximately 0.20 W/mK compared with other insulating materials.
However, a significant improvement in thermal conductivity is achieved through the subsequent evacuation process. This removes the gas molecules from the core, thereby further reducing convection significantly. Thermal conductivities of less than 0.004 W/mK are thus possible.

Efficiency
Save valuable space
The advantages of vacuum insulation panels lie in their exceptionally high thermal insulation performance compared with conventional insulation materials.
Compared with mineral wool, they require five times less space whilst delivering the same level of insulation. This results in significant economic and environmental benefits. It enables efficient insulation in areas where this was previously unthinkable. It also saves valuable space. In an era of urbanisation, with all its associated consequences, this represents a major advantage across all areas of application.

Processing
Easy to use
Although vakuVIP vacuum insulation panels are high-tech products, when used correctly they are just as easy to work with as any conventional insulation material.
On the contrary: The installation process is usually even quicker, as the panels are manufactured to size at the factory, meaning they no longer need to be cut to size on site. This helps to reduce costs on site.
Proper transport and storage, the installation of the VIP elements in accordance with the installation plan (construction) and installation instructions, as well as the correct handling of the insulation elements, guarantee optimal, long-lasting, high-performance insulation.

Ecology
Sustainability from A to Z
Saving energy is important. In an era of ongoing global warming, energy-efficient insulation is more important than ever. With vakuVIP products, you can help to reduce your energy consumption and minimise your impact on the environment.
With vacuum insulation from Vaku-Isotherm, you’re on the right track. We manufacture sustainably and energy-efficiently at our site in Frankenberg. As all production processes – from core manufacture to the finished VIP – take place in-house, we can recycle waste materials on site and benefit from short transport distances. Furthermore, our solar panel system helps us contribute to environmentally friendly energy generation.